Drivers

Original Prusa i3 MK3

RSS

Firmware 3.4.1 4 octobre 2018

Téléchargement 3.4.1 (7MB)

Changements dans 3.4.1

  • Filament runout detection fixed
  • Stealth mode bug (indicated as slow Z-axis movements) fixed
  • Message "Filament sensor response is poor, disable it?" has been temporarily disabled - this feature tended to be too sensitive and unreliable. We are working on improved version of this feature.
  • Statistics during active print fixed
  • OctoPrint "Printer reset detected" warning issue fixed

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 3.04 30 octobre 2018

Téléchargement (8MB)

Changements dans 3.04

  • Loading filament (updated chapter)
  • LCD screen (updated chapter)
  • Beeper settings (new chapter)
  • Language settings (new chapter)
  • MMU 2.0 (new chapter)
  • Slic3r PE (updated chapter)
  • Filament sensor (updated chapter)
  • Updating firmware (updated chapter)
  • Linearity correction (new chapter)

Original Prusa i3 MK2.5

RSS

Firmware 3.4.1 4 octobre 2018

Téléchargement 3.4.1 (7MB)

Changements dans 3.4.1

  • Filament runout detection fixed
  • Silent mode bug (indicated as slow Z-axis movements) fixed
  • Message "Filament sensor response is poor, disable it?" has been temporarily disabled - this feature tended to be too sensitive and unreliable. We are working on improved version of this feature.
  • Statistics during active print fixed
  • OctoPrint "Printer reset detected" warning issue fixed

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 2.5 2 mars 2018

Téléchargement (7MB)

Changements dans 2.5

Initial version

Original Prusa i3 MK3/MK2.5 Multi Material 2.0

RSS

Firmware 3.4.2 (V1.0.2) 20 octobre 2018

Téléchargement 3.4.2 (V1.0.2) (14MB)

Changements dans 3.4.2 (V1.0.2)

This firmware version is specifically for users who use MK2.5 + MMU2 setup. If you are not using MMU2 or if you use MMU2 with MK3 printer it is not necessary to upgrade to this version.

  • MK2.5 + MMU2 setup loudness reduced - For corrent beahviour it is necessary to use MMU firmware 1.0.2 and higher when running MMU2 with MK2.5. Users who use MK3 printer do not need to upgrade their MMU2 firmware.
  • MK2.5 + MMU2 setup initialization - MK2.5 was unable to automatically detect MMU2 unit after turning on the printer. This has been fixed.

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 1.0 30 août 2018

Téléchargement 1.0 EN (5MB)

Changements dans 1.0

  • Initial MMU 2.0 release

MK3/MK2.5 Multi Material 2.0  manuel dans les autres langues:
Čeština (v1.01) | English (v1.01)

Manuel d’assemblage du kit
Versions plus anciennes

Firmware 3.1.0 12 novembre 2017

Téléchargement 3.1.0

Changements dans 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Firmware 3.1.0 12 novembre 2017

Téléchargement 3.1.0

Changements dans 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Firmware 3.1.0 12 novembre 2017

Téléchargement 3.1.0

Changements dans 3.1.0

  • Linear Advance
  • Wizard
  • Host keep alive messages – better OctoPrint compatibility
  • Sorting files in SD card menu by date or name
  • Check if file is complete
  • First layer calibration – V2 integrated into FW
  • Auto power mode
  • XYZ calibration details menu improved
  • PID calibration safety check
  • M220: Speed factor
  • Saving E steps per mm to EEPROM fixed
  • Long filename scrolling is improved
  • Read more about this major version at prusaprinters.org
  • There’s a known bug using Repetier server, please wait for the next release if you’re using it

Drivers & Apps 2.2.1 27 octobre 2018

Changements dans 2.2.1

  • Slic3r 1.41.1
    • Custom supports - support blocker & enforcer modifier meshes
    • Improved quality of supports
    • Multi Material fixed and improvements
    • Bug fixes - see full changelog below
  • MK2.5 MMU2 Support
  • MK2.5 MMU2 G-codes
  • Added a link to New User Guides at the end of the installation

Handbook 1.05 16 octobre 2016

Téléchargement (6MB)

Changements dans 1.05

  • PEI surface preparation changes
  • calibration flow tweaks, when is needed to redo the calibration
  • how to change filament during a print
  • dental floss for object removing
  • light and full factory reset
  • firmware update

Firmware 3.0.12 23 juin 2017

Téléchargement 3.0.12

Changements dans 3.0.12

  • Amélioration de la calibration XYZ
  • Résultats de la calibration XYZ sont maintenant disponible dans le menu Support
  • Problèm Selftest régler
  • Amelioration du déchargement du filament
  • Multi Material
  • Quand l’impression est arreter, l’utilisateur sera demander quel filaments il faut décharger
  • “T?” Gcode rajouter, qui sélection quel extruder sera utiliser avant l’impression
  • Support pour la MK1 rajouter

Drivers & Apps 1.7.7 6 mai 2017

Changements dans 1.7.7

Slic3r PE upgraded to 1.34.1 – Up to 4x faster slicing thanks to parallelization

Other downloads

Rajout sur la carte RAMBo pour l’Arduino

  • Permet à Arduino IDE de télécharger le fichier FW. Si vous pouvez utiliser nos fichiers FirmwareUpdater et hexagonaux.
  • Télécharger

ColorPrint

Réglages pour Cura

Réglages pour Simplify3D

MK2 MMU V2 CALIBRATION

MK2/S V2 CALIBRATION

MMU Post Processor

  • Only for MMU 1 (not compatible with MMU 2.0)
  •  Download